搜索资源列表
UART
- LPC2103串口软件包，可以通过PC机显示出来。里面已经包含了所有串口常用函数。直接以C文件调用即可
LPC2103各种功能函数
- 有外部中断，定时器，RTC,IIC,A/D,UART,SPI,SSP等功能的函数，超实用
lpc2103-uart-communication LPC2103的UART串口调试程序
- LPC2103的UART串口调试程序,可是使用proteus仿真实现-philips lpc2103 arm7 uart communication program
LPC2103的第四个实验测试程序
- LPC2103的第四个实验测试程序：串口测试程序。在Protues7和 keil3中编译通过。里有说明的。,LPC2103 fourth experimental test procedure: serial test procedure. Keil3 in compiling Protues7 and through. There are described.
Uart
- LPC2103的串口通讯程序，采用自带库函数编写，实现PC机把指令发给控制器，控制器再把所接收数据返回上位机-LPC2103 serial communication procedure for the preparation of native library functions to achieve PC-to instructions issued to the controller, the controller then receives the data back to PC
PROJEKTARM
- LPC2103 - project (using UART, 1wire, interrupts)-LPC2103- project (using UART, 1wire, interrupts)
UART
- ARM7 LPC2103的UART驱动程序，学习LPC200系列的朋友可以参考下-ARM7 LPC2103' s UART driver, Friends of the study LPC200 series can refer to the next
DS18b_Uart
- 在EASY_ARM 2103上调试通过的DS18B20温度传感器，内含UART源代码，可直接在串口调试工具上显示，编译环境keil-ARM-EASY_ARM 2103 in debugging DS18B20 adopted temperature sensor, UART contains the source code can be directly displayed on the serial debug tools, compile environment keil-ARM
UART
- 基于LPC2103的串口程序，UART。ADS开发环境-Procedures based on the LPC2103 serial, UART. ADS development environment
start-NXP-lpc2103
- Simple program for start a new dev, lcd display, uart, adc for lpc2103 NXP arm7
UART
- 基于lpc2103的uart的示例程序，可以通过本人验证，这是能用的哦-uarst
UART
- 本程序在IAR环境中运行，其主控芯片是LPC2103,LPC2103支持两个UART总线接口，通过UART总线可以传输各种数据，可通过串口天使助手检查数据的传输，方便，效果好。-The program runs in the IAR environment, the master chip LPC2103, LPC2103 supports two UART bus interface, through the UART can transmit a variety of data bus ca
LPC2103_DS18B20
- LPC2103 + ADS 1.2 + DS18B20 + UART-LPC2103+ ADS 1.2+ DS18B20+ UART
UART
- 利用LPC2103的串行口发送数据。有查询和中断方式，ADS1.2编程。-Using LPC2103' s serial port to send data. For inquiries and interrupt mode, ADS1.2 programming.
UART0
- this sample code to use UART in lpc2103 microcontroller-this is sample code to use UART in lpc2103 microcontroller
hello_1
- LPC2103下UART通讯程序，使用UART0，经过试验通讯完全正常-LPC2103 UART communications under the program, use the UART0, tested completely normal communication
uart
- arm7 LPC2103系列程序串口收发程序 -arm7 LPC2103
uart
- LPC2103的UART串口调试程序,环境是Keil4的，代码涉及了LCD1602显示。-UART test Program for MCU NXP LPC2103!
IAR-LPC2103-UART
- 这个代码是LPC2103单片机的串口实验，用IAR软件编译的已经调试成功的。-this is LPC2103 uart.
LPC2103 peripheral
- LPC2103 interface via UART, GPIO, I2C ...